MatataTower Upgrade:

Upgrade Command Tower: Click Here::MatataTower Upgrade Instructions

MatataBot Upgrade:

STEP 1: If your device's SN Number Starting with "MTT1807", you need to finish "Pre-upgrade step" first. Click the link below to finish the "Pre-upgrade Step". If not, go to STEP 2.
The MTT1807 Pre-upgrade Instructions
STEP 2: Make sure your device's SN Number is not starting with "MTT1807", or have done the "Pre-upgrade Step" Click the link below to finish the MatataBot Update.
The MatataBot Upgrade Instructions

Download Resources:

Material for MTT1807:

1 x ST- LINK for MTT1807 Devices
Get ST-LINK Here:Matatalab SHOP - STLINK

Download Matata Code:

* Get our Matata Code APP on App Store by searching 'Matata Code'.
STEP 1: Get ready of the need-to-upgrade Command Tower, a Control board, a USB-C data line, a PC with WIN7 or newer system, an iPhone/iPad with MatataCode downloaded.
STEP 2: Run the upgrade software on a WIN-PC, and connect the Command Tower to the PC through a USB-C data line. Then turn on the Tower.
When the driver is not installed, the interface is as shown above. Click “Install the driver.”
STEP 4: Shut down the application, and dis-connect the Tower, and plug in the USB-C data line again. Turn on the application again, it shows the connection built.
STEP 5: Make sure the Tower is connected, click “Upgrade the system”.
STEP 6: Following the instruction of the application to start the upgrade. When this popup shows, press the Play button and keep pressing.
STEP 7: Click “OK”, wait until there is a progress bar, you can release the Play button.
STEP 8: Don't do anything, wait for the software to run automatically until you see "Upgrade completed" on the right.
STEP 9: After the upgrade is finished, click “Upgrade Bluetooth” to let the Tower enters into Bluetooth upgrade mode.
STEP 10: When you see it shows “DFU Start OK”on the message window, your Command Tower is ready for Bluetooth upgrade with the MatataCode 2.0.
STEP 11: Click “Upgrade” on the App, then find the device name “mdfutow” or “MataDfu”
STEP 12: The “MataDfu” is the Bluetooth name share by the old version Tower and MatataBot, you need the choose the right device type before you start to upgrade.
STEP 13: Enter into DFU upgrade, click “Start”
STEP 14: After the progress bar is fully loaded, restart the Command Tower to finish the upgrade.
* Get our Matata Code APP on App Store by searching 'Matata Code'.
* If you have any confusion when you are trying to upgrade your products, please contact us via Our Support Email.
This is only for MatataBot with SN starting with “MTT1807”.
Connect MatataBot and Win-PC through ST-link datalink provided by Matatalab, then turn on the MatataBot. Right-click on MatataBotUpgrade.exe, choose “Run as an administrator”.
Click the “Upgrade” button the start the upgrade. If it shows “upgrade fails”, please click “Install Driver” to setup the drive manually.
After the progress bar is 100% loaded, your MatataBot is ready for DFU upgrade with MatataCode App now.
Please check first the SN number on your MatataBot, and if it starts with “MTT1807”, please turn to the section: The MTT1807 pre-upgrade instructions.
Firstly, please download MatataCode 2.0 on your iPhone/iPad. MatataCode 2.0 only supports iOS 11.0 and newer. Android system will be available in the future.
Turn on MatataBot and make sure it is not connected to the Tower or Controller. (The blue light is blinking slowly)
Open MatataCode, change to “Upgrade” view. Click “Search” to search the device,, the device name of the MatataBot should be “MatataBot” or “Matalab”.
Click the device name and connect to MatataCode. Click “Ready”, then the MatataBot will enter into upgrade mode.
Click on “mdfubot” or “MataDfu” which is the device name of the MatataBot
After the device is connected to the App, click “DFU start” to start the DFU upgrade
After the progress bar is fully loaded, You will hear a cheer sound and some blinks of the LED eyes of MatataBot.
Congratulations, the upgrade is finished and your MatataBot is ready to play now.